Piseth

Objectives of the internship

Implement WSN(Wireless Sensor Network) with different use cases and security mechanism/protocol. Analyze and Evaluate.

alt Test Alt

Hardware

SmartRF06 EB (Evaluation Board)

SmartRF06 Evalution Board is used debug, flash, or act as power supply for other micro controllers like CC2538EM or sensortag CC2650.

• Power supply (Battery, USB pc or 5V external source, external source(3.6v))

SmartRF06 EB can be powered by several sources:

• • Batteries (two 1.5v batteries) [todo: image]

The image shows a switch for battery power source [todo: image switch]

• • USB (1.5v via PC usb port or external usb source) [todo: image]

USB switch for USB source (1.5v) [todo: image switch]

• • External source (3.6v)

pin used for external source (3.6v) [todo: image of the pin switch] (warning: not tested)

• • Reset Button

When connect to a microcontroller, SmartRF06EB, to some extents, is able to:

• • • Reset(restart) the microcontroller firmware by clicking reset button [todo: image]
    • Boot to bootloader(in case of CC2538) by holding select button while clicking reset button [todo: image]

Note: Have to have bootloader bit enable (link to cc2538 for more detail)

• Connect to other controller
  • CC2538 [todo: image]
  • Sensortag [todo: image]

Note: SmartRF06 has a jumper that allow debugging and flashing on some microcontroller possible. (XDS100v3). [todo: add image , write more detail]

CC2538 EM

• Power supply (throught EB or 3.3v usb)
• Ports connection
• What can CC2538 be used to

Compile Firmware

• Make command

Flash Firmware

• How to reset , go to bootloader (boodloader sequence check)
• CC2538-bsl
• Uniflash (Linux)**
• SmartRF Flash Programmer**
• Restore to Default firmware (Factory Firmware)

//**Note: Could be moved to Tools sections

CC2650 Sensortag

• What it can be used
• Power Supply (Through Sensortag DevPack (note: some usb cable doesn't work), Battery, CC2538)
• Default function of buttons (Disconnect, Reset to factory)

Compile Firmware

• Make command (Could point to contiki project structure section)

ex: make TARGET=srf06-cc26xx BOARD=sensortag/cc2650 cc26xx-web-demo.bin

Flash Firmware

• Flash via OAD
• Flash Default Factory Firmware
• Uniflash (Linux)**
• SmartRF Flash Programmer**

//**Note: Could be moved to Tools sections

CC2531 Dongle

• What it can be used. (Sniffer, Mote, Slip-radio)

Software and Platform

Software (Tools)

Uniflash

• Note: install for all user vs for root only

Sensniff

• cc2538 (project conf) : #define CC2538_RF_CONF_SNIFFER 1

                         #define CC2538_RF_CONF_CHANNEL 26

Components for Designed network

Motes

• What is motes
• What is it consist of and its functions
• What hardware can be used.

Network (WSN)

6lowpan

• Idea/why 6lowpan
• Basic function

Security

• Protocol implementation
• Right/Trusted Motes?
• Probe message attack (make mote wake up all the time)
• Relay Message?
• Exchange data
• What use cases/scenario

Issues faced

Compilation

Sometimes, when the output filetype is not specified (Ex: make TARGET=srf06-cc26xx BOARD=sensortag/cc2650), the compilation returns error with: [todo: image error text]

• Solution:

The problem could be solved by specify the output file. For example make TARGET=srf06-cc26xx BOARD=sensortag/cc2650 udp-client.bin

Pending to be Documented

• flash usb dongle
• access 6lbr embedded webserver from outside

Glossary

• RDC:
• ContikiMac:
• NullRDC:
• slip-radio:
• PANID: